Getting Started With Arduino

Prateek 18/10/2022

0 374 2 minutes read

Table of Contents

Introduction

Hi Everyone I Know you Learn Soo Much Arduino , But I will try to Explain Arduino in My Knowledge If You Learn Anything in This Article Please Comment Below…..

Arduino is Open-source Platform And is Very Easy To Learn The Microcontroller ,In first time Developed in Italy.

If You Want To Download the Software https://www.arduino.cc/en/software

Screenshot 2022 10 17 at 11.24.45 PM — Arduino IDE

In Market is Various Types Of Arduino Available Like Arduino Lilypad,Arduino micro,Arduino Nano,Arduino PRO Mini,Arduino UNO,Arduino Mega2560,ETC…….

Types Of Board

1.Arduino Pro-Mini

Arduino pro-mini is small microcontroller and is operating voltage will stated to 3.3V To 5v.

S.N.	Features	Value
1	Microcontroller IC	Atmega328
2	Digital Input/Output	14 (D0-D13)
3	Analog	8 (A0-A7)
4	PWM Pins	6
5	USB Port	Not Available
6	Built In Programmer	Not Available
7	SRAM	2KB
8	EEPROM	1KB
9	Flash Memory	32KB
10	Bootloader	0.5KB In Flash Memory
11	Operating Voltage	3.3V To 5V

2.Arduino Nano

Arduino nano is Also Small Microcontroller and is operating voltage is 3.3v To 5v .This Microcontroller is supported USB2.0 Mini B To USB2.0A.

S.N.	Feature	Value
1	Microcontroller IC	ATmega328p
2	Digital Input/Output Pin	14 (D0-D13)
3	Analog Pin	8 (A0-A7)
4	PWM Pin	6
5	Built In Progammer	Yes
6	USB port	Yes Avilable (Type-B Micro Usb)
7	flash Memory	32KB
8	SRAM Memory	2KB
9	EEPROM	1KB
10	Crystal Oscillator	16 MHz
11	Operating voltage	5V

3.Arduino UNO

Arduino UNO is a Best Board To stared The Programing With Arduino IDE .This Microcontroller is Supported The Dip Ic (ATmega328Pu IC),And The Operating Voltage is 3.3V , 5V or 9V .

Arduino UNO Is Available in market With DIP Ic And SMD IC.

S.N.	Feature	Value
1	Microcontroller IC	Atmega328p
2	Digital Input/Output Pin	14 (D0-D13)
3	Analog Pins	8 (A0-A8)
4	PWM Pins	6
5	USB Port	Yes (USB-A To USB-B)
6	Flash memory	32KB
7	SRAM	2KB
8	EEPROM	1KB
9	Crystal Oscillator	16MHz
10	Operating voltage	5v To 9V
11	ICSP Header	Yes

4.Arduino Mega

This Board Is not Small is very fast and Various pin Available .Arduino Mega is Advanced Level Microcontroller And is Supported USB Programming,Operating voltage is 3.3V To 12v.

S.N.	Features	Value
1	Microcontroller IC	Atmega2560
2	Digital Input/Output Pins	54
3	Analog Pins	16
4	PWM Pins	15
5	Built in programming	yes
6	USB Port	Yes (USB-A To USB-B)
7	Flash Memory	256KB
8	SRAM	8KB
9	EEPROM	4KB
10	Crysatl Oscillator	16 MHz
11	ICSP Header	Yes

Introduce Arduino IDE Software

I Will already Share the Arduino IDE Software Link https://www.arduino.cc/en/software You just Download the software And Open it Depending on your Operating System.

Explanation IDE

Just install the Software and open It then you sell like this ….

you just open the IDE And go to the tools and you see the different Boards Available, You Just Select the board Correctly

On Left Side, you see the verify and upload Symbol Available

if you type the code in the editor and you want to check whether the code will generate an error or not you just click the verify button then our code will compile and find the error.
if you want to Upload the code in the microcontroller you just click the Uploading Button fist you select the proper board and port.

And In the Right Side You just see the corner of the Serial monitor and Serial Plotter Available

Started With Arduino Nano Board

Arduino Nano With Serial Monitor

Here I Just Interface the Arduino Nano Board With Arduino IDE Software And I just write the code and Display the output in Serial Monitor.

Arduino With Serial Monitor — Arduino Nano with Arduino IDE

void setup() {

  Serial.begin(9600); 
}

void loop() {

  Serial.println("Hi Welcome To JustDoElectronics"); 
  
}

void setup() {

Serial.begin(9600);

}

void loop() {

Serial.println("Hi Welcome To JustDoElectronics");

}

1. Led Interfacing With Arduino Nano

Here I just interfacing with Arduino Nano Board

Arduino with Led — led interfacing with Arduino nano

I will connect the led in PIN D4

Anode – D4

GND – GND

Code

//Prateek
//www.justdoelectronics.com

void setup() {
  pinMode(D4, OUTPUT);
}

void loop() {
  digitalWrite(D4, HIGH);   
  delay(1000);                      
  digitalWrite(D4, LOW);    
  delay(1000);

//Prateek

//www.justdoelectronics.com

void setup() {

pinMode(D4, OUTPUT);

}

void loop() {

digitalWrite(D4, HIGH);

delay(1000);

digitalWrite(D4, LOW);

delay(1000);

2. Push Button Interfacing With Arduino Nano

Here I just interfacing the push Button, Led with an Arduino nano Board

The input Side is Connected to the push Button and the output side will glow the LED, when the button is pressed the led will be ON and if you release the push button then the LED will be OFF.

Circuit Diagram

//Prateek
//www.justdoelectronics.com

#define SWITCH_PIN 3
#define LED_PIN 12

int switchState;  // To store the state of switch

void setup() {
  // Set pin and D3 as input
  pinMode(SWITCH_PIN, INPUT);

  // Set pin D12 as output
  pinMode(LED_PIN, OUTPUT);

  // Turn off the LED initially
  digitalWrite(LED_PIN, LOW);
}

void loop() {
  // Read the states of the switches
  switchState = digitalRead(SWITCH_PIN);

  // Check if switch is pressed
  if (switchState == HIGH) {
    // Turn on LED
    digitalWrite(LED_PIN, HIGH);
  } else {
    // Turn off LED
    digitalWrite(LED_PIN, LOW);
  }

  // Delay for 100 milliseconds
  delay(100);
}

//Prateek

//www.justdoelectronics.com

#define SWITCH_PIN 3

#define LED_PIN 12

int switchState; // To store the state of switch

void setup() {

// Set pin and D3 as input

pinMode(SWITCH_PIN, INPUT);

// Set pin D12 as output

pinMode(LED_PIN, OUTPUT);

// Turn off the LED initially

digitalWrite(LED_PIN, LOW);

}

void loop() {

// Read the states of the switches

switchState = digitalRead(SWITCH_PIN);

// Check if switch is pressed

if (switchState == HIGH) {

// Turn on LED

digitalWrite(LED_PIN, HIGH);

} else {

// Turn off LED

digitalWrite(LED_PIN, LOW);

}

// Delay for 100 milliseconds

delay(100);

}

3. Potentiometer Interfacing With Arduino Nano

Here I just Interface the Potentiometer With Arduino Nano, when you rotate the potentiometer clockwise OR anticlockwise the LED will glow the potentiometer Value.

Circuit diagram

See In the circuit diagram potentiometer will connected to the Analog Pin (A0) And the led Will be Connected To the Digital Pin (D4).

//Prateek
//www.justdoelectronics.com

int LED_PIN = 4;

void setup() {
  Serial.begin(9600);
  pinMode(LED_PIN, OUTPUT);
}

void loop() {
  int analogValue = analogRead(A0);

  int brightness = map(analogValue, 0, 1023, 0, 255);

  analogWrite(LED_PIN, brightness);

  Serial.print("Analog: ");
  Serial.print(analogValue);
  Serial.print("_Brightness: ");
  Serial.println(brightness);
  delay(100);
}

//Prateek

//www.justdoelectronics.com

int LED_PIN = 4;

void setup() {

Serial.begin(9600);

pinMode(LED_PIN, OUTPUT);

}

void loop() {

int analogValue = analogRead(A0);

int brightness = map(analogValue, 0, 1023, 0, 255);

analogWrite(LED_PIN, brightness);

Serial.print("Analog: ");

Serial.print(analogValue);

Serial.print("_Brightness: ");

Serial.println(brightness);

delay(100);

}

#define POTENTIOMETER_PIN A0
#define BUZZER 5

void setup() {
  // Set pin A0 as input
  pinMode(POTENTIOMETER_PIN, INPUT);

  // Set pin D5 as output
  pinMode(BUZZER, OUTPUT);
}

void loop() {
  // Read the value of the rotary potentiometer
  int potentiometerValue = analogRead(POTENTIOMETER_PIN);

  // Map the potentiometer value to a frequency
  int frequency = map(potentiometerValue, 0, 1023, 100, 1000);

  // Set the buzzer frequency
  tone(BUZZER, frequency);

  // Delay for 100 milliseconds
  delay(100);
}

#define POTENTIOMETER_PIN A0

#define BUZZER 5

void setup() {

// Set pin A0 as input

pinMode(POTENTIOMETER_PIN, INPUT);

// Set pin D5 as output

pinMode(BUZZER, OUTPUT);

}

void loop() {

// Read the value of the rotary potentiometer

int potentiometerValue = analogRead(POTENTIOMETER_PIN);

// Map the potentiometer value to a frequency

int frequency = map(potentiometerValue, 0, 1023, 100, 1000);

// Set the buzzer frequency

tone(BUZZER, frequency);

// Delay for 100 milliseconds

delay(100);

}

4. LDR interfacing With Arduino Nano

#define LDR_PIN A1
#define LED_PIN 13

int ldrValue; // To store the value of the LDR
int threshold = 500; // The threshold value for turning the LED on and off

void setup() {
  // Set pin A1 as input
  pinMode(LDR_PIN, INPUT);

  // Set pin D13 as output
  pinMode(LED_PIN, OUTPUT);
}

void loop() {
  // Read the value of the LDR
  ldrValue = analogRead(LDR_PIN);

  // Check if the LDR value is less than the threshold
  if (ldrValue < threshold) {
    // Turn the LED on
    digitalWrite(LED_PIN, HIGH);
  } else {
    // Turn the LED off
    digitalWrite(LED_PIN, LOW);
  }

  // Delay for 100 milliseconds
  delay(100);
}

#define LDR_PIN A1

#define LED_PIN 13

int ldrValue; // To store the value of the LDR

int threshold = 500; // The threshold value for turning the LED on and off

void setup() {

// Set pin A1 as input

pinMode(LDR_PIN, INPUT);

// Set pin D13 as output

pinMode(LED_PIN, OUTPUT);

}

void loop() {

// Read the value of the LDR

ldrValue = analogRead(LDR_PIN);

// Check if the LDR value is less than the threshold

if (ldrValue < threshold) {

// Turn the LED on

digitalWrite(LED_PIN, HIGH);

} else {

// Turn the LED off

digitalWrite(LED_PIN, LOW);

}

// Delay for 100 milliseconds

delay(100);

}

5.LM35 Sensor Interfacing with Arduino Nano

const int lm35_pin = A2;	/* LM35 O/P pin */

void setup() {
  Serial.begin(9600);
}

void loop() {
  int temp_adc_val;
  float temp_val;
  temp_adc_val = analogRead(lm35_pin);	/* Read Temperature */
  temp_val = (temp_adc_val * 4.88);	/* Convert adc value to equivalent voltage */
  temp_val = (temp_val/10);	/* LM35 gives output of 10mv/°C */
  Serial.print("Temperature = ");
  Serial.print(temp_val);
  Serial.print(" Degree Celsius\n");
  delay(1000);
}

const int lm35_pin = A2; /* LM35 O/P pin */

void setup() {

Serial.begin(9600);

}

void loop() {

int temp_adc_val;

float temp_val;

temp_adc_val = analogRead(lm35_pin); /* Read Temperature */

temp_val = (temp_adc_val * 4.88); /* Convert adc value to equivalent voltage */

temp_val = (temp_val/10); /* LM35 gives output of 10mv/°C */

Serial.print("Temperature = ");

Serial.print(temp_val);

Serial.print(" Degree Celsius\n");

delay(1000);

}

6.RGB LED Interfacing With Arduino

#define RED 9
#define GREEN 10
#define BLUE 11

void setup() {
  // Set pins D9, D10, and D11 as output (Based on kit specs)
  pinMode(RED, OUTPUT);
  pinMode(GREEN, OUTPUT);
  pinMode(BLUE, OUTPUT);
}

void loop() {
  // Set the RGB LED to red
  digitalWrite(RED, HIGH);
  digitalWrite(GREEN, LOW);
  digitalWrite(BLUE, LOW);

  // Delay for 1 second
  delay(1000);

  // Set the RGB LED to green
  digitalWrite(RED, LOW);
  digitalWrite(GREEN, HIGH);
  digitalWrite(BLUE, LOW);

  // Delay for 1 second
  delay(1000);

  // Set the RGB LED to blue
  digitalWrite(RED, LOW);
  digitalWrite(GREEN, LOW);
  digitalWrite(BLUE, HIGH);

  // Delay for 1 second
  delay(1000);

  // Turn off the RGB LED
  digitalWrite(RED, LOW);
  digitalWrite(GREEN, LOW);
  digitalWrite(BLUE, LOW);

  // Delay for 1 second
  delay(1000);
}

#define RED 9

#define GREEN 10

#define BLUE 11

void setup() {

// Set pins D9, D10, and D11 as output (Based on kit specs)

pinMode(RED, OUTPUT);

pinMode(GREEN, OUTPUT);

pinMode(BLUE, OUTPUT);

}

void loop() {

// Set the RGB LED to red

digitalWrite(RED, HIGH);

digitalWrite(GREEN, LOW);

digitalWrite(BLUE, LOW);

// Delay for 1 second

delay(1000);

// Set the RGB LED to green

digitalWrite(RED, LOW);

digitalWrite(GREEN, HIGH);

digitalWrite(BLUE, LOW);

// Delay for 1 second

delay(1000);

// Set the RGB LED to blue

digitalWrite(RED, LOW);

digitalWrite(GREEN, LOW);

digitalWrite(BLUE, HIGH);

// Delay for 1 second

delay(1000);

// Turn off the RGB LED

digitalWrite(RED, LOW);

digitalWrite(GREEN, LOW);

digitalWrite(BLUE, LOW);

// Delay for 1 second

delay(1000);

}

7.DHT11 Sensor With Arduino

/*
Example for Embedded DHT11 Sensor in 9-in-1 Expansion Board for Arduino Uno.
By: RoboticX Team
*/
#include <DHT.h>

#define DHTPIN 4 // Digital pin D4 connected to the DHT sensor

DHT dht(DHTPIN, DHT11); // Initialize DHT sensor

void setup() {
  // Set up serial communication
  Serial.begin(9600);

  // Initialize DHT sensor
  dht.begin();
}

void loop() {
  // Read temperature and humidity
  float temperature = dht.readTemperature();
  float humidity = dht.readHumidity();

  // Print temperature and humidity to serial monitor
  Serial.print("Temperature: ");
  Serial.print(temperature);
  Serial.print("°C");
  Serial.print(" Humidity: ");
  Serial.print(humidity);
  Serial.println("%");

  // Delay for 2 seconds
  delay(2000);
}

Example for Embedded DHT11 Sensor in 9-in-1 Expansion Board for Arduino Uno.

By: RoboticX Team

#include <DHT.h>

#define DHTPIN 4 // Digital pin D4 connected to the DHT sensor

DHT dht(DHTPIN, DHT11); // Initialize DHT sensor

void setup() {

// Set up serial communication

Serial.begin(9600);

// Initialize DHT sensor

dht.begin();

}

void loop() {

// Read temperature and humidity

float temperature = dht.readTemperature();

float humidity = dht.readHumidity();

// Print temperature and humidity to serial monitor

Serial.print("Temperature: ");

Serial.print(temperature);

Serial.print("°C");

Serial.print(" Humidity: ");

Serial.print(humidity);

Serial.println("%");

// Delay for 2 seconds

delay(2000);

}

8.16×2 Lcd interfacing With Arduino Nano

Here, I just connected the 16×2 LCD with Arduino nano Board.

//Prateek
//www.justdoelectronics.com

#include &lt;LiquidCrystal.h&gt;

const int RS = 12, EN = 11, D4 = 10, D5 = 9, D6 = 8, D7 = 7;
LiquidCrystal lcd(RS, EN, D4, D5, D6, D7);

void setup() {
  lcd.begin(16, 2);

  lcd.setCursor(0, 0);
  lcd.print("Welcome To");
  lcd.setCursor(2, 1);
  lcd.print("justdoelectronic");
}

void loop() {
}

//Prateek

//www.justdoelectronics.com

#include <LiquidCrystal.h>

const int RS = 12, EN = 11, D4 = 10, D5 = 9, D6 = 8, D7 = 7;

LiquidCrystal lcd(RS, EN, D4, D5, D6, D7);

void setup() {

lcd.begin(16, 2);

lcd.setCursor(0, 0);

lcd.print("Welcome To");

lcd.setCursor(2, 1);

lcd.print("justdoelectronic");

}

void loop() {

}

9.Ultrasonic Sensor Interfacing with Arduino Nano

Here, I just connected to the Ultrasonic Sensor with Arduino Nano microcontroller

ArduinWithultersonicsensor — Ultrasonic Sensor with Arduino Nano

Circuit Diagram

Arduino with ultrasonic sensor — Arduino Nano

//Prateek
//www.justdoelectronics.com


int trigPin = 4;
int echoPin = 3;

float duration_us, distance_cm;

void setup() {

  Serial.begin(9600);
  pinMode(trigPin, OUTPUT);
  pinMode(echoPin, INPUT);
}

void loop() {
  digitalWrite(trigPin, HIGH);
  delayMicroseconds(10);
  digitalWrite(trigPin, LOW);

  duration_us = pulseIn(echoPin, HIGH);
  distance_cm = 0.017 * duration_us;
  Serial.print("distance: ");
  Serial.print(distance_cm);
  Serial.println(" cm");
  delay(400);
}

//Prateek

//www.justdoelectronics.com

int trigPin = 4;

int echoPin = 3;

float duration_us, distance_cm;

void setup() {

Serial.begin(9600);

pinMode(trigPin, OUTPUT);

pinMode(echoPin, INPUT);

}

void loop() {

digitalWrite(trigPin, HIGH);

delayMicroseconds(10);

digitalWrite(trigPin, LOW);

duration_us = pulseIn(echoPin, HIGH);

distance_cm = 0.017 * duration_us;

Serial.print("distance: ");

Serial.print(distance_cm);

Serial.println(" cm");

delay(400);

}

THANKS

Introduction

Types Of Board

Introduce Arduino IDE Software

Explanation IDE

Started With Arduino Nano Board

Arduino Nano With Serial Monitor

1. Led Interfacing With Arduino Nano

2. Push Button Interfacing With Arduino Nano

3. Potentiometer Interfacing With Arduino Nano

4. LDR interfacing With Arduino Nano

5.LM35 Sensor Interfacing with Arduino Nano

6.RGB LED Interfacing With Arduino

7.DHT11 Sensor With Arduino

8.16×2 Lcd interfacing With Arduino Nano

9.Ultrasonic Sensor Interfacing with Arduino Nano

Prateek

Gps & Gsm location Tracking System Using Arduino

Leave a Reply

Related Articles

GPS Tracker using Arduino | Sim800l

Automatic grass cutting machine using arduino

Solar Tracking System Using Arduino

Water Level Sensor Tutorial

Adblock Detected