Screenshot 2023 01 02 at 8.20.54 AM e1687519565477

Build Your Smart GPS Tracker System Using Arduino

GPS Tracker Using Arduino

Prateek 02/01/2023

10 83,240 2 minutes read

Table of Contents

Introduction

GPS System is very commonly used in every field Like Vehicle Tracking, Human Tracking, Ship Tracking, And Bicycle Tracking System. In this tutorial, I will also create a small GPS tracker device to find the latitude and Longitude (GPS Coordinates) And Speed.

Small GPS Tracker uses component’s GPS Neo-6m, Sim800l, Arduino Nano,16×2 LCD Display, Push Button And Buzzer.

Check Small Watch GPS Track

We Have Also built many types Of Vehicle Tracking Systems If You are Interested Plz Check Out

Bill Of Materials

S.N	Component's	Quantity	Link To Buy
1	Arduino Nano	1
2	GPS Neo-6m Module	1
3	GSM Sim800l Module	1
4	16x2 LCD Display	1
5	I2C Module	1
6	10k Pot	1
7	Push Button	1
8	Buzzer	1
9	Zero PCB	1
10	12V DC Supply	1

All impotent Component Are Required To Do This Project

Arduino Nano

This one is the Pin Diagram of Arduino nono microcontroller

GSM Sim800l Module

SIM800l GSM Module, designed by Simcom. This module operates at a voltage of 3.4v to 4.4v, it is powered directly with a lithium-ion battery and LM2596 step-down converter.

The comes with an IPX antenna interface that allows switching between a PCB antenna and a suction cup antenna.

Note – The Module is compatible with any 2G-3G SIM card.

Led status indicator

The sim800l module has an LED indicator that shows the network conduction.

Blinking every 1 second – The module is powered on but not connected to the network.
Blinking every 2 seconds – The GPRS data connection is active and ready for data Transfer.
Blinking every 3 seconds – The Module is connected to a network and ready to send/receive SMS messages And Calls.

GPS Neo-6m Module

The Neo-6M GPS module is developed by U-blox.

The GPS Module in Full form is (the Global Positioning System) it uses 31 satellites orbiting Earth to transmit location and date/time.

Led indicator

on the neo-6M GPS Module Board, there’s is a small LED that shows the condition of communication status with satellite:

No, blinking means the GPS module is searching for satellites.
Blinking Every 1 Second Means the position is fixed and is connected to the satellite.

Check awesome GPS Based Projects

GPS Tracker using Arduino | Sim800l

Push Button

10K Resister

Zero PCB

Block Diagram

PCB Design

Circuit Diagram

In this circuit diagram, we connect the all components properly Like…

Sim800l GSM Module connected to the PIN D7 And D8.
Neo-6m GPS Module connected to the PIN Rx.
I used Two push buttons and is connected to the PIN D4 And D5.

Here I used the 3.7v lithium-ion battery to power up the whole circuit and also connected the TP4056 Charging Module to charge the lithium-ion battery.

Because the Sim800l GSM Module Is working from 3.6v to 4.2v That’s why I used the Battery if I gave the more power it did not work properly.

Code

TinyGPS.h

TinyGPS

Select the Arduino Nano Board And Upload the code.

Before uploading the code just Change the number

char phone_no[] = "+91xxxxxxxxxx";

1	char phone_no[] = "+91xxxxxxxxxx";

……………………………………………………..

This code is valid for SMS & Call

//Prateek
//www.justdoelectronics.com

#include <TinyGPS.h>
#include <SoftwareSerial.h>
#include <Wire.h>
SoftwareSerial Gsm(7, 8);
char phone_no[] = "+9188305848xx";  //For SMS
TinyGPS gps;
int state;
String textMessage;

void setup() {
  Serial.begin(9600);
  Gsm.begin(9600);
  delay(2000);

  Serial.print("AT+CMGF=1\r");
  delay(100);
  Serial.print("AT+CNMI=2,2,0,0,0\r");
  delay(100);
  pinMode(4, INPUT);
  pinMode(5, INPUT);
}

void loop() {

  bool newData = false;
  unsigned long chars;
  unsigned short sentences, failed;

  for (unsigned long start = millis(); millis() - start < 1000;) {
    while (Serial.available()) {
      char c = Serial.read();
      Serial.print(c);
      if (gps.encode(c))
        newData = true;
    }
  }
  if (Gsm.available() > 0) {
    textMessage = Gsm.readString();
    textMessage.toUpperCase();
    delay(10);
  }

  state = digitalRead(4);
  if (state == 1)  //When Button is Press
  {
    float flat, flon;
    unsigned long age;
    gps.f_get_position(&flat, &flon, &age);
    Gsm.print("AT+CMGF=1\r");
    delay(400);
    Gsm.print("AT+CMGS=\"");
    Gsm.print(phone_no);
    Gsm.println("\"");
    Gsm.println("Alert I need help.............");
    Gsm.print("http://maps.google.com/maps?q=loc:");
    Gsm.print(flat == TinyGPS::GPS_INVALID_F_ANGLE ? 0.0 : flat, 6);
    Gsm.print(",");
    Gsm.print(flon == TinyGPS ::GPS_INVALID_F_ANGLE ? 0.0 : flon, 6);
    delay(200);
    Gsm.println((char)26);
    delay(200);
    Gsm.println();
    delay(10000);
  } else {
    delay(10);
  }

  state = digitalRead(5);
  if (state == 1)  //When Button is Press
  {

    Serial.println("OK");
    delay(20000);
    Gsm.println("ATD+9188305848xx;");  //For Call
    delay(150000);
    Gsm.println("ATH");
    delay(1000);

  } else {
    delay(10);
  }
  Serial.println(failed);
}

//Prateek

//www.justdoelectronics.com

#include <TinyGPS.h>

#include <SoftwareSerial.h>

#include <Wire.h>

SoftwareSerial Gsm(7, 8);

char phone_no[] = "+9188305848xx"; //For SMS

TinyGPS gps;

int state;

String textMessage;

void setup() {

Serial.begin(9600);

Gsm.begin(9600);

delay(2000);

Serial.print("AT+CMGF=1\r");

delay(100);

Serial.print("AT+CNMI=2,2,0,0,0\r");

delay(100);

pinMode(4, INPUT);

pinMode(5, INPUT);

}

void loop() {

bool newData = false;

unsigned long chars;

unsigned short sentences, failed;

for (unsigned long start = millis(); millis() - start < 1000;) {

while (Serial.available()) {

char c = Serial.read();

Serial.print(c);

if (gps.encode(c))

newData = true;

}

if (Gsm.available() > 0) {

textMessage = Gsm.readString();

textMessage.toUpperCase();

delay(10);

}

state = digitalRead(4);

if (state == 1) //When Button is Press

{

float flat, flon;

unsigned long age;

gps.f_get_position(&flat, &flon, &age);

Gsm.print("AT+CMGF=1\r");

delay(400);

Gsm.print("AT+CMGS=\"");

Gsm.print(phone_no);

Gsm.println("\"");

Gsm.println("Alert I need help.............");

Gsm.print("http://maps.google.com/maps?q=loc:");

Gsm.print(flat == TinyGPS::GPS_INVALID_F_ANGLE ? 0.0 : flat, 6);

Gsm.print(",");

Gsm.print(flon == TinyGPS ::GPS_INVALID_F_ANGLE ? 0.0 : flon, 6);

delay(200);

Gsm.println((char)26);

delay(200);

Gsm.println();

delay(10000);

} else {

delay(10);

}

state = digitalRead(5);

if (state == 1) //When Button is Press

{

Serial.println("OK");

delay(20000);

Gsm.println("ATD+9188305848xx;"); //For Call

delay(150000);

Gsm.println("ATH");

delay(1000);

} else {

delay(10);

}

Serial.println(failed);

}

This Code Is valid for Only Text SMS

//Prateek
//www.justdoelectronics.com

#include <SoftwareSerial.h>
#include <TinyGPS.h>
#include <Wire.h>

SoftwareSerial Gsm(7, 8);           // RX, TX pins for GSM module
char phone_no[] = "+91883058xxxx";  // Put Your phone number
TinyGPS gps;
int buttonState;
unsigned long buttonPressTime;
bool isSMSsent = false;

void setup() {
  Serial.begin(9600);
  Gsm.begin(9600);

  Gsm.print("AT+CMGF=1\r");
  delay(100);

  Gsm.print("AT+CNMI=2,2,0,0,0\r");
  delay(100);

  pinMode(4, INPUT_PULLUP);
}

void loop() {
  bool newData = false;
  unsigned long chars;
  unsigned short sentences, failed;

  for (unsigned long start = millis(); millis() - start < 1000;) {
    while (Serial.available()) {
      char c = Serial.read();
      Serial.print(c);  // Output GPS data to the Serial Monitor
      if (gps.encode(c))
        newData = true;  // Check if there is new GPS data
    }
  }

  buttonState = digitalRead(4);

  if (buttonState == LOW) {  // Button is pressed
    if (!isSMSsent) {
      buttonPressTime = millis();

      float flat, flon;
      unsigned long age;
      gps.f_get_position(&flat, &flon, &age);

      Gsm.print("AT+CMGF=1\r");
      delay(400);
      Gsm.print("AT+CMGS=\"");
      Gsm.print(phone_no);
      Gsm.println("\"");
      Gsm.println("Alert I Need help...");
      Gsm.print("http://maps.google.com/maps?q=loc:");
      Gsm.print(flat == TinyGPS::GPS_INVALID_F_ANGLE ? 0.0 : flat, 6);
      Gsm.print(",");
      Gsm.print(flon == TinyGPS::GPS_INVALID_F_ANGLE ? 0.0 : flon, 6);
      delay(200);
      Gsm.println((char)26);
      delay(200);

      Serial.println("SMS Sent");
      isSMSsent = true;
    }
  } else {
    isSMSsent = false;
    delay(10);
  }

  Serial.println(failed);
}

//Prateek

//www.justdoelectronics.com

#include <SoftwareSerial.h>

#include <TinyGPS.h>

#include <Wire.h>

SoftwareSerial Gsm(7, 8); // RX, TX pins for GSM module

char phone_no[] = "+91883058xxxx"; // Put Your phone number

TinyGPS gps;

int buttonState;

unsigned long buttonPressTime;

bool isSMSsent = false;

void setup() {

Serial.begin(9600);

Gsm.begin(9600);

Gsm.print("AT+CMGF=1\r");

delay(100);

Gsm.print("AT+CNMI=2,2,0,0,0\r");

delay(100);

pinMode(4, INPUT_PULLUP);

}

void loop() {

bool newData = false;

unsigned long chars;

unsigned short sentences, failed;

for (unsigned long start = millis(); millis() - start < 1000;) {

while (Serial.available()) {

char c = Serial.read();

Serial.print(c); // Output GPS data to the Serial Monitor

if (gps.encode(c))

newData = true; // Check if there is new GPS data

}

buttonState = digitalRead(4);

if (buttonState == LOW) { // Button is pressed

if (!isSMSsent) {

buttonPressTime = millis();

float flat, flon;

unsigned long age;

gps.f_get_position(&flat, &flon, &age);

Gsm.print("AT+CMGF=1\r");

delay(400);

Gsm.print("AT+CMGS=\"");

Gsm.print(phone_no);

Gsm.println("\"");

Gsm.println("Alert I Need help...");

Gsm.print("http://maps.google.com/maps?q=loc:");

Gsm.print(flat == TinyGPS::GPS_INVALID_F_ANGLE ? 0.0 : flat, 6);

Gsm.print(",");

Gsm.print(flon == TinyGPS::GPS_INVALID_F_ANGLE ? 0.0 : flon, 6);

delay(200);

Gsm.println((char)26);

delay(200);

Serial.println("SMS Sent");

isSMSsent = true;

}

} else {

isSMSsent = false;

delay(10);

}

Serial.println(failed);

}

Demo Of Project

When you press the push button after a few seconds the GSM sends the text message with the proper GPS coordinates.

Then you receive the call at the same number if you want to receive the call at a different number then change the code.

Video Tutorial

10 Comments

Srinjoy Das says:

24/08/2024 at 7:54 pm

This project is not working I have did exact same connection also uploaded the code its not working please help
KRISHNA MURARI says:

10/09/2024 at 7:18 am

This code is not working please help
Prateek dwivedi says:

14/09/2024 at 9:23 pm

How to wireing in women safety project in GPS tracker give a video
Anonymous says:

24/09/2024 at 10:18 pm

Why code is not working
Prateek says:

25/09/2024 at 10:13 am

used the 2 code is work properly
Prateek says:

25/09/2024 at 10:13 am

used the 2 code is work properly
richard says:

01/10/2024 at 1:00 am

Please I would like to ask if you design and sale pc boards. If yes am interested and would like some samples for my prototype project. My regards
user says:

08/10/2024 at 7:56 pm

can u give me the pcb file?? mail it at ajmalsworkshop@gmail.com
Jayanta dalnaik says:

11/10/2024 at 9:21 pm

hello sir, i used code 2, but it is not working.. plz reply
vedanth says:

16/10/2024 at 2:07 pm

ardino doesnt consist of wire.h library

Introduction

Bill Of Materials

Arduino Nano

GSM Sim800l Module

GPS Neo-6m Module

Push Button

10K Resister

Zero PCB

Block Diagram

PCB Design

Circuit Diagram

Code

Demo Of Project

Video Tutorial

Prateek

Smart Shopping Cart Using RFID & Arduino

Fingerprint Door Lock System

10 Comments

Leave a Reply

Related Articles

GPS Tracker using Arduino | Sim800l

Automatic grass cutting machine using arduino

Solar Tracking System Using Arduino

Water Level Sensor Tutorial

Adblock Detected